-
When This Checklist Applies
-
Step 1: Map the Wiring Topology Before You Touch Anything
-
Step 2: Calculate Total Load—Not Per-Bulb Wattage
-
Step 3: Select the Right Driver—and Don't Substitute a Laptop Power Supply
-
Step 4: Wire in Parallel for Multi-Light Fixtures
-
Step 5: Integrate the Zigbee Controller at the Right Point
-
Step 6: Test Each Branch Before Final Assembly
-
Step 7: Document the Wiring—Every Time
-
Common Mistakes That Cause Callbacks
When This Checklist Applies
This is for commercial lighting installers and facility teams wiring multi-light chandeliers—the kind with 6, 8, or 12 individual lamp holders on a single canopy—into a Zigbee-controlled lighting system. If you're wiring a single-bulb pendant, skip this. If you're retrofitting a hotel lobby fixture on a 48-hour deadline, this is exactly what you need.
I coordinate rush lighting installs for B2B clients. In March 2024, a 14-light chandelier for a banquet hall landed on-site 36 hours before the event, with a Toshiba Zigbee module already spec'd. The electrician had wired plenty of standard fixtures but never a multi-light model to a smart system. We walked through seven steps over the phone. Here they are.
Seven steps. Roughly 3-4 hours for an 8-light fixture, assuming the wiring is accessible and you have the right driver on hand.
Step 1: Map the Wiring Topology Before You Touch Anything
Most multi-light chandeliers are wired in parallel—each socket gets full line voltage. But not all of them. Some older or low-voltage fixtures use series wiring, where the circuit daisy-chains from socket to socket.
How to tell: open the canopy and look at the junction. Parallel wiring has two main leads splitting out to each socket. Series wiring runs one wire through all sockets in a chain. If you see series and you're installing LED bulbs, stop. You'll need a different driver configuration, or you'll be replacing bulbs every few weeks.
We missed this on a 2022 install. Assumed parallel, wired it up, burned through four bulbs before the electrician called me. Cost us $200 in replacement bulbs and a second site visit. Now we send a topology photo before quoting any job.
Step 2: Calculate Total Load—Not Per-Bulb Wattage
This is where a lot of installers get tripped up. You're not sizing the driver for one bulb. You're sizing it for the sum of every bulb in the fixture.
An 8-light chandelier with 5W LED bulbs pulls 40W total. A 12-light fixture with 7W bulbs pulls 84W. Add 20% headroom for inrush current and thermal margin. That 84W fixture needs a driver rated for at least 100W. Run it at 84W without headroom and you'll be replacing the driver within a year—usually in the middle of a lease term.
The question everyone asks is "what wattage bulb?" The question you should ask is "what's the total load on the driver?" Because that number determines whether your system runs cool or cooks itself.
One caveat: this math assumes your bulbs are actually rated at the wattage on the box. Cheap LED bulbs often run 10-15% above their stated wattage. If you're importing bulbs without a datasheet, measure actual draw with a clamp meter before sizing the driver.
Step 3: Select the Right Driver—and Don't Substitute a Laptop Power Supply
Here's an industry blindspot I see constantly: people see "power supply" and assume any power supply works. They don't.
A Toshiba laptop power supply outputs a fixed DC voltage (usually 19V for laptops) with current limited by the load. An LED driver outputs either constant current (for most LED fixtures) or constant voltage (for LED strips). They are not interchangeable. Plugging a laptop power supply into an LED fixture will either underdrive it (dim output) or overdrive it (premature failure). I've seen both.
For a Toshiba LED driver, match the output current to the fixture's spec. Most commercial multi-light chandeliers use constant-current drivers in the 350mA to 700mA range. Check the fixture label before you buy anything. Toshiba's driver lineup includes models for both constant-current and constant-voltage applications—pick the one that matches your fixture, not the cheapest one on the shelf.
I keep a spreadsheet of driver specs for every fixture we've installed in the last three years. It's saved us from at least a dozen wrong-part orders. When a rush order comes in, we check the spreadsheet first, then call the supplier. In that order.
Step 4: Wire in Parallel for Multi-Light Fixtures
Assuming Step 1 confirmed parallel wiring (or you've converted the fixture), connect each socket's live and neutral leads to the main feed in parallel. All live leads to the live feed, all neutral leads to the neutral feed. Ground, if present, bonds to the canopy.
Don't daisy-chain sockets in series unless the fixture was designed that way. Series wiring means one failed bulb kills the whole fixture—not a great look for a hotel lobby at 6 PM on a Friday.
Three things to check before you close the canopy: connections are tight (tug-test each one), no exposed copper, and the fixture's rated voltage matches your supply. In that order. The tug-test catches more weak connections than any meter will.
Step 5: Integrate the Zigbee Controller at the Right Point
Zigbee lights don't work without a controller. The controller goes between the power supply and the fixture—or, if you're using a Zigbee dimmer, at the wall switch. For chandelier installs, the in-canopy module is usually cleaner and avoids running extra wire.
Wire the Zigbee module according to its diagram: line in, neutral in, load out to the driver, neutral out to the fixture. Pair the module with the gateway before you close the canopy. Pairing after installation means you're up on a ladder with a phone at arm's length from the fixture, which is exactly as fun as it sounds.
Per the Zigbee 3.0 specification (Connectivity Standards Alliance, 2023), devices should be paired within 10 feet of the coordinator during commissioning. Verify your module's pairing procedure before you install—Toshiba's Zigbee modules pair via a button sequence that varies by model. I've had installers spend 45 minutes on a pairing step that would've taken 5 with the right sequence.
Step 6: Test Each Branch Before Final Assembly
Energize the fixture with all bulbs installed and the Zigbee module paired. Check three things: every bulb lights, dimming works (if applicable), and there's no flicker at low dim levels.
Flicker at low dim is the most common issue with LED and Zigbee. Usually it's a driver compatibility problem—the driver's minimum load isn't being met, or its dimming curve doesn't match the Zigbee module's output. If you see flicker, don't just live with it. Swap the driver for one rated for your actual load and dimming setup. The right driver costs less than the callback.
This is where those 20 minutes of testing save you a two-hour return trip. Trust me on this one.
Step 7: Document the Wiring—Every Time
Take photos of the wiring before you close the canopy. Write down the driver model, the Zigbee module model, the bulb wattage, and the total load. Tape the specs inside the canopy if there's room.
Why does this matter? Because six months later, someone—maybe you, maybe a different electrician—will need to replace a driver or add a bulb. Without documentation, they're guessing. And guessing on a commercial lighting system means either overbuying parts or undersizing them.
I've learned to ask "what's NOT documented?" before "what's the problem?" on every service call. The undocumented fixtures are always the ones that take three visits to fix.
Common Mistakes That Cause Callbacks
Here's what we see most often, based on our internal data from 200+ multi-light installs:
- Wrong driver type. Constant-current driver on a constant-voltage fixture (or vice versa). Check the label—actually read it, don't assume.
- Undersized driver. No headroom means premature failure. Add 20% above total load.
- Series wiring with LED bulbs. One fails, all go dark. Convert to parallel if the fixture allows it.
- Zigbee module paired too far from the gateway. Pair at close range, then install.
- No documentation. The next installer—or the next you—will hate the person who skipped this step.
One more thing: if a supplier quotes you a driver price that looks too good, ask what's included. Shipping? Mounting hardware? Warranty? I've seen "cheap" drivers cost 40% more once the extras were added. The vendor who lists everything upfront—even if the total looks higher—usually costs less in the end. That's not a sales pitch. It's what our invoice records show over three years of purchasing.
This checklist reflects our experience as of January 2025. Verify current driver specs and Zigbee pairing procedures against the manufacturer's documentation—Toshiba's product line and the Zigbee specification have both been updated in the past year. This worked for us on standard commercial fixtures with accessible canopies; if you're dealing with sealed architectural fixtures or proprietary socket systems, the wiring approach changes and you should consult the fixture manufacturer before proceeding.